JeeHell FMGS forums

Hi I'll give up (for now) and just have to accept this strange spin behavior. For me, it's definitely not the FPS issue. I've tested (LSZH/28 and DEGE1X) with "clear skies" and thick clouds, and I sometimes get over 70 FPS, and it happens there too. What I know now is that when this happen...

Hello Jose I imagine these mini PCs have enough power to visually display the PFD and ND, the two ECAMs, and the MCDU. The question is more whether you have enough outputs for the monitors. I think the FMGS server must be installed on the main computer in any case, and I recommend a LAN network conn...

Hi Dieter You're absolutely right, every system is different, and all settings probably need to be checked and reviewed. I finally had success and was able to noticeably improve my frames by switching AA from 8xMSAA to 2xSSAA. Clouds also have a strong impact on me—which is probably why I experience...

Hello Dieter I have a fundamental question about your solution. Is it simply about keeping the FPS stable above 30, and could this also be achieved with a different setting (e.g., setting the scenery complexity to low)? In any case, thank you very much for your input! I adopted the settings as they ...

it's not the USB hub for me

Okay, I have a suspicion... I recently optimized my cockpit and connected my TCA Airbus Stick and Elgato StreamDesk to a other USB hub. I didn't plug in the power connector because it's not practical. My suspicion is that either the USB hub is temporarily shutting down because it doesn't have enough...

Hello Dieter Thank you for your advice. Do you have limited or unlimited FPS? I had the same problem again yesterday (ActiveSky Weather 10.03.2025 19:35Z) on my flight from LSZH to LSGG (VEBIT1T VEBIT T50 ROTOS Z669 ULMES ULMES2R) shortly after takeoff and before BREGO and I wasn't in the clouds and...

Another possibility: did you install the hardware module "Skalarki I/O" when installing the JeeHell A320? You may have to install this afterwards.
Good luck!

Hi Dieter i find this solution in my documents: Das Display der MCDU hatte immer schwarze Ränder und hat nicht sauber in den kleinen Monitor gepasst. Habe in den Windows-Einstellungen das Display auf 1280x1024 gesetzt (1:1:25) und es passt wunderbar The MCDU display always had black edges and didn't...

Hello everyone I think I found a flight where I can reproduce this situation and I think it has something to do with the FPS, as JeanLuc writes. Here are my requirements: - SimBrief Flightplan: LSZH/28 N0326F140 VEBI1X VEBIT T50 ROTOS Z669 ULMES ULME2R LSGG/22 - ActiveSky Weather from 25.02.2025 19:...

Hello Chris
could it be that your MCDU is for the FO side?
go to the Skalarki Profiler - Stop Profile - IO Test... see if it says A320 MCDU CD or A320 MCDU FO connected.
Then you can click on this and by pressing any button on the MCDU you can see whether the button works (lights up green)
Good luck!

Hi Dieter
I also have this problem. We had this here
https://jeehell.org/forum/viewtopic.php?t=289
mentioned. I haven't received a solution yet and am back to 61.11

It has also happened to me that he switched to "Direct Law". The plane is very difficult to control then.
Most of the time, I don't know if it has anything to do with how quickly I press the pause button, he continued to fly in Normal Law

Hi stefangr Yes, this was the case for me too. The problem is that it is not reproducible. It always appears at a different time and in a different place. The pause helped me the last two times. I had it active for about 20 seconds each time. It feels like something isn't working (like with YouTube ...

Hello Fritz This happens to me from time to time too - unfortunately. I also have stable over 30fps. I'm not sure if it's because of FSHud. Do you use it? What strangely helps me is if I immediately activate the pause, wait a moment and deactivate the pause again. Then I can catch the plane and cont...

Hello JeanLuc Unfortunately, loading using TOPCAT doesn't work for me, even with version 61.13.2. A bar appears in P3D and it says that I have filled up with 8800kg of fuel using TOPCAT, for example. But I have 700/3010/0/2310/700 = 6720kg in the tanks. If I load again, I have 700/3710/0/2310/700 = ...

okay.
For years I have been using SIMstarter NG to start the A320FMGS\Starter.exe and then the Prepar3d.exe and have never had any problems with it.
What would be the correct order in your opinion?

Hi JeanLuc With the latest version B61.13.1 I have a new problem with the fuel weight. I load it with TopCat and P3D shows me that I have loaded e.g. 5800kg. In the ECAM it only shows me 4390kg (it's not always the same). When the engines are running, I had a GW of 4400kg. I think something is wrong...

Hi Dieter
i have the 5.1.600.1000 and have no problem with delays.

Here is my first feedback: - the engine sound (in idle) gets slightly louder after about 15 seconds and then quieter again and starts again from the beginning - I miss the sound when the landing gear is extended and retracted and when the flaps move in and out. Of course I don't know if these sounds...

I was able to download the Sound.exe and also have engine sound.
I have under ...\A320FMGS\Sound\Sounds\ACFT sounds\CFM\sound.cfg
[GROUND_ROLL]
the value
minimum_speed=5.00//0.00
entered and now the "conveyor belt" noise is gone when stationary

Hello Sebastian
Did you install the FLAPS panel and SPOILER panel software when installing FMGS and are they open?
Then you would have to close them - I had a similar problem and JeanLuc wrote this to me

Hello JeanLuc I tested the new sound module again. Here is my feedback: - after starting P3D, a loud noise is heard, as if the plane was crashing onto the runway - then a noise in an endless loop like that of a conveyor belt can be heard - if I delete the contents of the folder ...\A320FMGS\Aircraft...

As I understand it, the Skalarki Profiler belongs on the P3D computer and you enter the IP address of the second computer in the top right of this profiler. You enter the calibration and definition of the keys in the Jeehell Config menu on the second computer and this transfers the values ​​to the P...

Hi Massimo
No idea if there is an entry in an ini file. Try renaming the Updater.exe in the A320FMGS folder to Updater.exe.off.