A320 FMGS B61

[jeehell]

Hello,

here is the latest version:
https://www.jeehell.org/A320FMGS_B61.10.1.exe
Please also see this post about beta sound module:
https://jeehell.org/forum/viewtopic.php?t=233
It will become the new standard in a version or 2, so it's still open for suggestions etc...


The release log:
08/10/2024 B61.10.1
-Fixed SPLRs issues despite correct calibration


29/09/2024 B61.10.0
- Fixed pack not starting in case of XBLEED feeding with onside engine failed
- Fixed ECAM on single screen not cycling STS page properly
- Enhanced reverser behavior (acft won't move forward in idle REV)
- Fixed ALT CSTR not held on approach in some conditions
- Fixed VNAV profile when same ALT CSTR is on several points on the APPR route

25/08/2024 B61.9.0
-Fixed PFD/ND sometimes XFR'd on elec power up
-Work on probe heating computers (elec power and ecam display in case of faults)
-Fixed FDS USB MCDU issue (dataline not set, only on USB version)
-Fixed GPWS SYS button OFF inhibiting other FWC synthetic voice sounds (radio alts, etc)
-Fixed FCU/PFD selected speedifferent sometimes d
-Fixed PLAN mode not showing while ADIRS are aligning (initial ADIRS alignment is still needed ~30s)
-Fixed baro setting inhg/mb not correctly initializing with hardware
-Fixed pressurization LDG ELEV always reseting o 0ft in descent

21/05/2024 B61.4.2
-Fixed issues with ADIRS alignment,On BAT LED
-Fixed issues with FAC CG computation (FWC warnings should be more accurate)
-Fixed some SIOC Creator config issues with MCDUs
-Fixed StarterENGrun
-Fixed ADIRS LCD display in OVHD GUI
-Fixed V/S Indicator going out of scale at very high values
-Fixed some V/DEV scale logic issues with FLS/SLS/RNAV approaches
-Fixed LOC scale or VOR lateral deviation scale blinking continuously sometimes


04/04/2024 B61.3.9
-Fixed issues with steering

25/03/2024 B61.3.8
-Fixed issues with steering and A/BRK

20/03/2024 B61.3.7
-Reworked flight model
-Reworked FBW, mostly in roll and yaw channels
-Cosmetic changes on EIS (flags mostly)
-Fixed hold at PPOS changing when craeting a new TMPY FPLN
-Fixed some FLS/SLS/ILS/FINAL modes issues
-MCDU GUI: config now with a readable config file, may need to reconfigure it at first run. Fixed potential openGL issue with it.

[Soarbywire]

Thank you JL!

[balu69]

Thank you very much for continuing to work on the P3D version!

[masterp]

Thank you very much for continuing support FSX.
I installed the latest 61.3.7, only issue so far is the tiller has no effect, nose wheel steering is not working… axis of Tiller in FMGS Config is normal.

[jeehell]

Try to put the files in the zip file below into your FMGS Server\PERF folder:
https://www.jeehell.org/PERF.zip

[pete_fuss]

Hi JL,
with the version B61.3.8 the problems after landing always there, no chance to steer with the steering tiller or the rudder

regards

[michael1508]

Hi Jean Luc,

What has changed from B61.3.9 to 61.4.2?

Thx,
Michael

[jeehell]

For me everything works, so I dont know. Could be old version of P3D/FSX which causes that.
Try to edit C:\A320FMGS\FMGS Server\PERF\CFM\aircraft.ini with following lines:

Code: Select all

[AIRCRAFT]
useP3Dtiller=no
RudderToTillerPositionBinding=yes

Try various settings here for these two lines (yes/no etc)

[architfly1]

Thank You is much for your hard work.

Just having a little issue, quick align of IRS not working. Kindly suggest a solution.

[gillesaqsim]

hi,
i use to the mech CALLS of 21VU (Ovh) which is not used in JL and I assigned it in fmgs-config (buttons) to ALIGN ADIRS at the end of the list, push event...
i use it when passengers are in a hurry!

[Buford]

Download of B61.9.0 via updater in my case failed on all PCs. Downladed .exe after "Failed Twice" has 0 KB. Download link here at the top works.

[Beret_ch]

Hi Jeehell
With the B61 I have a delay on the Flightcontrol on around 3 to 4s. On the B60 is all ok. Anyone the same problem?

[jeehell]

There is no reason here, except if something is slowing down the software. Post your FMGS server logs at least.
Did you redo calibration and navdata?

[Beret_ch]

I've found the error. Have forgot to run as admin. Now it looks good.