P3d v6
-
- Posts: 216
- Joined: Thu Dec 15, 2022 11:11 am
- Location: Germany \ near EDDL
- Contact:
P3d v6
Has anyone tested v6 with jeehell?
Regards
Dieter
A320 cockpit Prepar3d v5.4 with full voice control for ATC and ground crew
Developer of EWD Overlay and Home Cockpit Builder
Dieter
A320 cockpit Prepar3d v5.4 with full voice control for ATC and ground crew
Developer of EWD Overlay and Home Cockpit Builder
Re: P3d v6
Hello JL!
I´ve try now 3 time to start the airbus.
If i set the trottle to flex (take off) and arrive the take off speed and what to take off the signal input the sidestick take no effect.
The aircraft do not take off.
Cought it be possible that there is a problem with the connection between p3d v6 und jeehell?
Best regards
peter
SimpatchLog.txt
20:28:40 CL LINEARIZED removed a changed entry 0000018876543D28
20:28:40 change table error CL LINEARIZED
20:28:40 ZeroLiftAlpha removed a changed entry 0000000000000000
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 TBL404 removed a changed entry
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
FMGSServerlog.txt
****Log Recycled at: 20:40:59.96
****Timer1 start 14467703
-FMGSphase:2 14467703
-ECAM INOP OK
-GPWS OK
-RADNAV...
SimApiUpdate OK
Autotune skipped
-RADNAV OK
-SOUND OK
-AP OK
-FCTL law OK
-FCU Display OK
-MCDU1 OK
-MCDU2 OK
-Turn radius calculated OK
-Lateral calculations OK
-XTK and sequencing OK
-FPLN tracking OK
- not Calculating VDEV.
-FPLN tmp tracking OK
-Turn radius calculated OK
-Lateral calculations OK
-XTK and sequencing OK
-FPLN sec tracking OK
-Turn radius calculated OK
-Lateral calculations OK
-XTK and sequencing OK
-EOSID tracking OK
autoland OFF
-LEDs Update OK
-FCU MAP OK
-PFD/ND/SPEEDS MAP OK
-VMCA OK
-TCAS MAP OK
-MCDU1 MAP OK
-MCDU2 MAP OK
****Timer1 Completed 14467703
Main loop timing:0.012
I hope the logfiles helps.
Best regards
peter
I´ve try now 3 time to start the airbus.
If i set the trottle to flex (take off) and arrive the take off speed and what to take off the signal input the sidestick take no effect.
The aircraft do not take off.
Cought it be possible that there is a problem with the connection between p3d v6 und jeehell?
Best regards
peter
SimpatchLog.txt
20:28:40 CL LINEARIZED removed a changed entry 0000018876543D28
20:28:40 change table error CL LINEARIZED
20:28:40 ZeroLiftAlpha removed a changed entry 0000000000000000
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 change table error ZeroLiftAlpha
20:28:40 TBL404 removed a changed entry
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
20:28:40 change table error TBL404
FMGSServerlog.txt
****Log Recycled at: 20:40:59.96
****Timer1 start 14467703
-FMGSphase:2 14467703
-ECAM INOP OK
-GPWS OK
-RADNAV...
SimApiUpdate OK
Autotune skipped
-RADNAV OK
-SOUND OK
-AP OK
-FCTL law OK
-FCU Display OK
-MCDU1 OK
-MCDU2 OK
-Turn radius calculated OK
-Lateral calculations OK
-XTK and sequencing OK
-FPLN tracking OK
- not Calculating VDEV.
-FPLN tmp tracking OK
-Turn radius calculated OK
-Lateral calculations OK
-XTK and sequencing OK
-FPLN sec tracking OK
-Turn radius calculated OK
-Lateral calculations OK
-XTK and sequencing OK
-EOSID tracking OK
autoland OFF
-LEDs Update OK
-FCU MAP OK
-PFD/ND/SPEEDS MAP OK
-VMCA OK
-TCAS MAP OK
-MCDU1 MAP OK
-MCDU2 MAP OK
****Timer1 Completed 14467703
Main loop timing:0.012
I hope the logfiles helps.
Best regards
peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Hello JH!
Here are the most log-files zippet.
Best regards
Peter
I try to start p3d V6 then the rest of my programs (like ActiveSky, jeehell, simsounds etc.)
All work included the engine start.
What i remember was that sometimes my tiller does not really work, after a few minutes it came back.
And if i set the throttle into flex the aircraft begin very slowly to run.
And it war unpossible to take off.
The flight befor with p3d V5 works without any problems.
Best regards
Peter
Here are the most log-files zippet.
Best regards
Peter
I try to start p3d V6 then the rest of my programs (like ActiveSky, jeehell, simsounds etc.)
All work included the engine start.
What i remember was that sometimes my tiller does not really work, after a few minutes it came back.
And if i set the throttle into flex the aircraft begin very slowly to run.
And it war unpossible to take off.
The flight befor with p3d V5 works without any problems.
Best regards
Peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Hello!
I tried today again!
And after i push the trottle on flex and begin to run there is a message with "change table error TBL404"
I hope the messsage helps.
Best regards
peter
I tried today again!
And after i push the trottle on flex and begin to run there is a message with "change table error TBL404"
I hope the messsage helps.
Best regards
peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Hello JL!
It might be a bigger problem?
Best regards.
Peter
It might be a bigger problem?
Best regards.
Peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Hello JL!
Sorry give me 1hr. Then it is only!
LG.peter
Sorry give me 1hr. Then it is only!
LG.peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
I want to attach as zip file. But not possible.
And as text file not too!
What can i do?
Best regards
peter
Here is the way to my cloud!
https://1drv.ms/u/s!Ak5vXfAwc7Fbg4FRu0S ... g?e=2qUUKh
Best regards
And as text file not too!
What can i do?
Best regards
peter
Here is the way to my cloud!
https://1drv.ms/u/s!Ak5vXfAwc7Fbg4FRu0S ... g?e=2qUUKh
Best regards
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Hello JL!
Have you got it?
best regards
peter
Have you got it?
best regards
peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Your simpatcher log indicates it fails after roughly 30 minutes.
There can be several reasons for that unfortunately.
Did you do anything particular? Like changing vehicle for another livery?
How did you adapt the installation to P3D v6?
There can be several reasons for that unfortunately.
Did you do anything particular? Like changing vehicle for another livery?
How did you adapt the installation to P3D v6?
Regards,
Jean Luc
Jean Luc
Re: P3d v6
Hello JL!
I lost the control on the runway if i set the trust on flex and the aircraft begin to run.
At first the aircraft is going on the left side and did not react on the sidestick!
It is not possible to take off.
After some seconds sometimes the input from the sidestick works and the aircraft is taking off but it is shooted over the runway.
I install all like the v5.
I checked it with the v5? All is fine!
Best regards for your help.
Peter
I lost the control on the runway if i set the trust on flex and the aircraft begin to run.
At first the aircraft is going on the left side and did not react on the sidestick!
It is not possible to take off.
After some seconds sometimes the input from the sidestick works and the aircraft is taking off but it is shooted over the runway.
I install all like the v5.
I checked it with the v5? All is fine!
Best regards for your help.
Peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
There is n v6 option in the current installer, how did you install the aircraft and simpatch into v6?
Regards,
Jean Luc
Jean Luc
Re: P3d v6
I copy all files from "documents" (p3d v5 files and p3d v5 add-ons) and "appdata" p3d v5 to p3d v6.
And all works until the aircraft getting run at the runway (all is working overhead, throttle (trimwheel), Glare, MCDU).
I get the message "change table error TBL404".
Do you know whats wrong?
best regards
peter
And all works until the aircraft getting run at the runway (all is working overhead, throttle (trimwheel), Glare, MCDU).
I get the message "change table error TBL404".
Do you know whats wrong?
best regards
peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
paste here the contents of "A320FMGSinstall path"\simpatch\simpatchConfig.ini
Regards,
Jean Luc
Jean Luc
Re: P3d v6
hello JL!
Here is the content of the simpatchConfig.ini
[config]
sleepTime=120000
Best regards
peter
Here is the content of the simpatchConfig.ini
[config]
sleepTime=120000
Best regards
peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Hello JL!
I checked the change the "sleepTime to 180000"
So i can take off!
But i checked that my PFD at cpt and fo-side have a time laps of several seconds and i can not activate the AP (no AP1 or AP2) and after
a few seconds i lost the control off the plane.
How can i check the problem?
best regards
peter
I checked the change the "sleepTime to 180000"
So i can take off!
But i checked that my PFD at cpt and fo-side have a time laps of several seconds and i can not activate the AP (no AP1 or AP2) and after
a few seconds i lost the control off the plane.
How can i check the problem?
best regards
peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Hello JL!
I´ve tested again with V6 but everytime if i start i lose the connection between fmgs and the aircraft.
At the rotade-speed i can rotate but i can't activate the "AP1".
It makes me crazy.
Where can i have a look whats wrong?
Best regards
Peter
I´ve tested again with V6 but everytime if i start i lose the connection between fmgs and the aircraft.
At the rotade-speed i can rotate but i can't activate the "AP1".
It makes me crazy.
Where can i have a look whats wrong?
Best regards
Peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
try to reduce your graphics settings, make sure you always get 30fps or more (ideally around 60).
Do you have FMGS Server on the same PC as P3D?
Do you have FMGS Server on the same PC as P3D?
Regards,
Jean Luc
Jean Luc
Re: P3d v6
Hello JL!
Yes i have it at the same computer!
What the problem is, is that i lost the connection if i rotate.
Befor all is nice i can start the engine can roll at the taxi at the runway can check the flightcontroll.
The autotrust is coming on the start.
Really weard.
best regards
peter
Yes i have it at the same computer!
What the problem is, is that i lost the connection if i rotate.
Befor all is nice i can start the engine can roll at the taxi at the runway can check the flightcontroll.
The autotrust is coming on the start.
Really weard.
best regards
peter
----------------------------------------------
D-AIPB
D-AIPB
Re: P3d v6
Now I installed v6 in addition to 5.3. Exactly the same issue I already had with 5.4 appears: Sometimes on descent, but sometimes already beginning with the TO roll the displays of JeeHell begin to stutter, whole JeeHell seems to loose connection to the sim for a second on and on, until the aircraft gets out of control, makes a 180 around the longitudinal axes and crashes inevitably. There must habe been a change from v5,3 to 5.4 causing this trouble.
Fps are around or above 30.
Fps are around or above 30.
See you in the skies…
Re: P3d v6
Hallo Buford
I had absolute the Same issues for just 4 Month. Now i have a 4 PC Setup. And I Changed my hole Setup and install the FMGS Server from P3d PC to the SD/ Engine Display PC and now all Problem are gone away…
Greetings
Jochen
I had absolute the Same issues for just 4 Month. Now i have a 4 PC Setup. And I Changed my hole Setup and install the FMGS Server from P3d PC to the SD/ Engine Display PC and now all Problem are gone away…
Greetings
Jochen