SPD BRK DISAGREE in V61.10

What's new
Post Reply
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

SPD BRK DISAGREE in V61.10

Post by pete_fuss »

Hello JL,
yesterday i installed the new version 61.10 and take since there two flights.
in both flights i cannot use the Speedbrakes in Flight, then i got the mastercaution F/CTL SPD BRK DISAGREE and in blue SPD BRK LEVER....Retract.
But when i was landing and the speedbrakes are armed, the coming up.
What can happend or what make i wrong?
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
jeehell
Site Admin
Posts: 414
Joined: Thu Nov 03, 2022 10:14 am

Re: SPD BRK DISAGREE in V61.10

Post by jeehell »

How did you setup your spd brk lever and particularly the armed detent?
Regards,
Jean Luc
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

Image
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

in the last version it works
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

Hi JL,
now i switch the arming zone from the anlaog range to a switch.
but i cannot use the speddbrakes in flight.
regards Pete
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
jeehell
Site Admin
Posts: 414
Joined: Thu Nov 03, 2022 10:14 am

Re: SPD BRK DISAGREE in V61.10

Post by jeehell »

is it a joystick axis or does it come from a hardware module?
Regards,
Jean Luc
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

it is a joystick axis, i think a leobodnar board
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

hello jl,
this morning i did some tests because of the spoiler error.
first i started the software spoiler panel and realised that the lever is set to full when the spoilers are retracted. then i deactivated the spoiler axle in the fmgsconfiger and tried to extend the spoilers with the software panel, without success. then captnpero gave me the tip to change the values of the spoiler axle in the configer. now i can extend the spoilers but my lever is set to retracted when the spoilers are extended! did you change the axles or where can i change something for myself?
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

Hi again,
now i take a testflight, but in the air i cannot bring the spoilers to work, there it comes the master cautchen spd brk disagree.
at landing the armed speedbrakes come up and on ground i can use the spoilers, but with reversed lever.
now i go back to version 61.9
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
jeehell
Site Admin
Posts: 414
Joined: Thu Nov 03, 2022 10:14 am

Re: SPD BRK DISAGREE in V61.10

Post by jeehell »

I believe 15% for neutral is a bit too much. This probably overlaps with your armed range. Try a smaller 5% first?
Regards,
Jean Luc
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

Hi JL,
a new report of testing.
i make a 5% neutral error,and the master Caution of the speed brakes are still there!
Then i go back to the version 61.9.0 with the same control.xml and the spoiler work correctly.

back to 61.10.0 and the master caution with the spoilers is back.
so i stay at the version 61.9. and i can fly normaly
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
jeehell
Site Admin
Posts: 414
Joined: Thu Nov 03, 2022 10:14 am

Re: SPD BRK DISAGREE in V61.10

Post by jeehell »

I found the bug late last night. I will put an update as soon as I can.
Regards,
Jean Luc
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

Hi,
was i the only one how use this update?
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
gillesaqsim
Posts: 86
Joined: Fri Nov 04, 2022 5:36 pm

Re: SPD BRK DISAGREE in V61.10

Post by gillesaqsim »

hello pete, this update is too recent, no time to test yet... ;)
regards from Bordeaux
pete_fuss
Posts: 39
Joined: Fri Nov 04, 2022 6:49 am

Re: SPD BRK DISAGREE in V61.10

Post by pete_fuss »

Hello JL,
wit the version 61.10.1 it works again.
regards from ETHL

Pete Fuss
P3D 5.4 ,Ryzen 7 5800X 3.80 GHz with 32 GB ,RTX3080 TI 12GB, MIxed Homecockpit + JH FMGS V B69.10.1, AS/ASCA, RdShade +Tex, CorteManager + ExtPWR from CaptPERO, a lot of add-on sceneries a round europe and the world
Post Reply