Tiller Steering

[jeehell]

Ok it seems you saved the log after shutting down the aircraft?
Can you do it while the software is running, on the ground with tiller not working but engines running etc?

[hamsterpilot]

Yeah I uploaded the log after closing the simulator. So I just let it running, taxi a bit and then upload it bevor closing jeehell and p3d?

[jeehell]

the log must be saved when the problem happens, so it is while taxiing "normally" but the steering is not working.

[hamsterpilot]

I will fly another round. Just to be sure, saving means closing Jeehell FMGS right?

[jeehell]

No, saving is just copying the log file somewhere else so it's not written to anymore

[hamsterpilot]

Here you go. I made mutliple saves just in case. The tryingToTaxiWithTiller log might be the interesting one

[LH320]

I installed version B61.3.8 this morning and did a short flight.
The tiller worked, but the sensitivity felt a little different. I calibrated the tiller again.
Parking brake also works again. I am using P3Dv6.

[joao.fernandescmte]

I also noticed a greater sensitivity, however the tiller works in the taxi for takeoff but after landing it is not possible to leave the runway as the tiller loses its action

[LH320]

I also noticed a greater sensitivity, however the tiller works in the taxi for takeoff but after landing it is not possible to leave the runway as the tiller loses its action

I can confirm this. The tiller does not work after landing.

[hamsterpilot]

The Logs I provided contains one before take off where tiller was working and one after landing where it wasn't. I hope that helps him to find the problem.

[jeehell]

can you look into c:\A320FMGS\FMGS Server\PERF\aircraft.ini if you have an entry for useP3Dtiller
Try to put the line useP3Dtiller=yes in any case

[gillesaqsim]

Hi Jean-Luc, yes this entry is alreaydy present on the 2 aircraft.ini (CFM and IAE) and no tiller after landing. i use the 61.3.8 on my local test platform.
question: i suppose that you don't have this issue!? what do you use what do you have as platform config.
i 'll test a short LFBD/LFBD flight now and back to you.
best regards
gilles

[gillesaqsim]

same issue after test.
curiously, during taxiing before takeoff, regularly while the plane does not touch the tiller, the plane starts to go to the right. I have to move the tiller so that it comes back straight.
also would you like me to spy on some offsets during the flight to identify the wolf? (fsuipc offset)

[hamsterpilot]

A few days I noticed when I closed Jeehell before P3D after having the tiller issue, the flightmodel directly retracted the landing gear. It didnt do that before. Maybe this helps to pin point the problem.

[balu69]

and has with me "aviaWorx Approach Report" showed that "Gear not in Landing Configuration", even though I took the gear out - maybe this will help - this with the B61.3.7

[hamsterpilot]

I flew a round now, can confirm in both aircraft.ini useP3Dtiller=yes.
Again the tiller didn’t work after landing and when closing Jeehell the flight model instantly retracted the landing gear. Also the “Rudder to Tiller Position binding” in the aircraft options can’t be selected to yes, the dropdown menu doesn’t open.

[jeehell]

Those having issues, do you have FMGS server on a remote PC?
And those not having any issues?

[hamsterpilot]

I have everything on the same Computer wich is running P3D. Only exceptions are the PFD/ND and ECAM displays which are running on a separate PC

[snooky_g]

Hi all, joing this thread, as I´m facing the tiller issue as well, but FMGS Server installed on a remote PC. (P3D 5.4, FMGS B31.3.7, aircraft.ini files including "useP3Dtiller=yes")

Regards, Stefan

[gillesaqsim]

Me too, fmgs sever on p3d computer

[LH320]

The FMGS server is also running on a remote PC on my side.

[joao.fernandescmte]

I have 3 machines, the server is on the main one and the other 2 only run the panels (PFD, ND, ECAN) and the mcdu. Still having problems here. I went back to B60.1.5.exe

[jeehell]

Hello

I just put a new version online, hopefully this will fixed the steering issue, which was linked to the gear state.

Let me know after testing.

[hamsterpilot]

You did it! The tiller works again! Thank you for your efforts

[snooky_g]

I can confirm, the tiller is again working as expected with B61.3.9. Many thanks, Jean Luc !!