JeeHell FMGS forums

Update II: After the updates have been installed the new installation was still running fine - at my office room beside my desk. I carried then the computer to the simulator room pluged it in, started everything, adjusted the size of PFD & ND according the screen size in the cockpit, did anothe...

New Update I: There seems to be a "weird phenomenon" in a Windows 11 update. After I had no other idea, I simply completely reinstalled the small PC yesterday. Lo and behold - PFD & ND for the captain side are running reliably so far. I will now activate the group policy to allow Wind...

Hi Jean Luc, I forgot to mention: All my sim PC's are in a seperate VLAN, not allowed to communicate to the outside (except to P3D for licensing and Updates of known software products) Windows Updates are comming from my internal WSUS server and have to be approved for the group of sim PC's. The las...

Hello, since two days - like always, I didn't change anthing :D - my PFD & ND looses its connection to the FMGS server after a few seconds. They pop up after a start or restart, showing the expected content, are "connected" and green in the FMGS-Server Window and then get red and "...

A bit more information and a few words about your environments could help to give you an answer.
A simple statement "cannot start the engine" doesn't invite anybody to give you a helping hand.

This has been resolved Fun fact 1: The Throttle Lever for ENG 2 was inside the Skalarki profiler configured as "Loudspeaker" Don't ask me why, I've never been there... Fun fact 2: For the levers I would suggest to do a calibration inside the profiler and in the Jeehell axis configuration....

Hi all, I've a total strange issue with the Skalarki Throttle Lever. Everything is working quite well. Only the lever for ENG 2 can't be calibratet and has no fuction at all. The whloe Skalarki Pedestal is connectet to a slave PC an the issue shouldn't be a fundamental configuration problem, cause l...

Hello Stephan, Thanks for your many tips, but when it comes to Simconnect I don't think you're quite on the right track. According to my information - and many tests in the past - I only need Simconnect if I run the FMGS server on a machine other than the simulator (P3D). That's not the case for me ...

Hi Michael & snooky_g, both of your comments pointed me to the right direction. @Michael: First of all, Skalarki Profiler seems to be required just on systems with connected Sklarki hardware. But - thinking about your idea leads me to check my profiler setup on the Pedestal PC. And I have found ...

can you try running Profiler on the same pc as FMGS server? This works fine for me. I have both running on a dedicated JL server pc, separate from the P3D pc. Hi Michael, just to be sure: Profiler on the Main PC even there is no Skalarki hardware connected? Questions regarding your setup: - Do you ...

I also think that you have to enter the IP address of the FMGS server in the Pedestal PC profiler. I assume that you have connected your skalakri hardware to both the main and pedestal PC. I also assume that the profiler is running on both devices. Does the hardware not work on both PCs? What I als...

I also have Skalarki hardware, but unlike your setup everything is installed on a single PC. I don’t know how a multiple PC setup is supposed to work. Do you have to configure the profiler with the IP address of the PC running the simulator? Hi, this is a good question... Following my logic (and th...

balu69 wrote: ↑Fri Apr 19, 2024 9:58 pm Hi
Have you the "P3D V6.0" and "Master P3D PC" installed?

Hi Stephan,
yes of course "Master P3D PC" & P3D V6.0" is tagged on the "Main PC"

regards
Robert

I'm afraid I can't see the forest for the trees right now, but I'm having a problem setting up skalaki hardware and P3D v6 together with JeeHell. Maybe someone has a little tip for me: Main PC: P3D, Jeehell with (FMGS Server, EGPWS logic, Sound module, FSUIPC support, SKALARKI I/O) and FSUIPC v6 reg...