JeeHell FMGS forums

Your sim patch log indicates a problem.
Do you have particular addons?
Try to change the sleep time in simpatch.ini file to a higher value. (180000 is a minium, try 240000).
Avoid changing stuff from P3D menus as much as possible.

Hi Markus
best would be to ask them directly about compatiblity?

Try this DLL:
https://www.jeehell.org/JeeHell_IIT_v2.dll
(keep the old one safe, outside of hardware connect folder)

that already exists, check 78ED value 35

The rounding are probably always "round down" then. Which gives you this result. I don't recall exactly what was put there. And I will not change it because there is no issues in any case.

Geez, do you realize that the accuracy of the FOB and each tank is +/-10 kg, which means that depending on rounding what you see is therefore correct?
2134 is rounded down to 2130
2134+2134=4268 rounded up to 4270

SIOC (or more correctly open cockpit boards) is known to sometimes badly initialize switch state, that could be your issue (particularly if nothing happens without the switch declared).

fCU is for the FCU. The button on the sticks is AP TO. (Take over).

is it on all airports, even default one?
You should try to manually create the navdatabase (not with corte manager) by launching the FMGS Server with admin rights. And make sure your G:\prepar3D v5 folder is not protected (read only or else)

For me everything works, so I dont know. Could be old version of P3D/FSX which causes that.
Try to edit C:\A320FMGS\FMGS Server\PERF\CFM\aircraft.ini with following lines: Try various settings here for these two lines (yes/no etc)

you will not see any difference in the software behavior wether its sys1 or sys2 so I left only ON/OFF.

You also need a release action in the pedal disc button.

As for the actual action, there may be some settings to change in fmgs server\perf\cfm\aircraft.ini that you can play with but that's not easy

The file that contains the data is IIT.xml.
If you have it untouched since last crash post it so I have a look.

78EE is a write only offset, there are no bits to read. It has nothing to do with skalarki.

Hello

I am sorry I do not understand your question?

ah I found the issue, the CPTKeys.ini I sent does NOT have the key combination somehow, BLANK2 line is empty.
You can edit the file and modify the line as below:
BLANK2=SHIFT+L

it seems hardware connects picks up delay.
Either the computer running it is too slow, or the networking has bandwidth issue.
Or another hardware module is clogging it up. You mentionned SIOCmodule, mayb can you try to isolate that module to another PC?

yo ucan try to go in FMGS Server -> options and toggle "Pitch Trim Wheel Feedback"

Yes MAJ is French for SHIFT, it slipped in during translation...
in your A32OFMGS\softwarePanels folder you may check you have CPTkeys.ini (and/or FOkeys.ini).
Eventually replace it by the file attached here. (jsut rename to FOkeys.ini for FO side).

Some chipsets probably don't handle well opengl, it's not a problem with power itself but hardware/drivers. Also maybe at 600x600 it overlaps to another screen or is outside screen area?

Hi

No problem to have a remote IIT module.

As for your question on toggle switches, it depends on the switch, but for 2 positions toggle switches that should be OK. Do some tests as you build your config and you should tell when it works or not as it should.

Hello do you use the legacy FDS interface or the new one (selection at installation)? as for the switches assignments, it may depend on the switch. Some do not care about the released action and only require a push event to work. For korry-like switches, if you have the latching on the switch, it is...

Your screenshot and log do not show simpatcher working, as balu says you may need to wait a bit longer for that to be conclusive

Is the date of the file from the day you are flying or from before reinstalling?

The most likely cause is simpatcher not declared properly or crashing at some point.